Home > Company News > 
SFK TIH 100M/230V

SFK TIH 100M/230V

Medium induction heater

High heating capacity of up to 120 kg bearing

The SKF medium induction heater TIH 100m has the same high standards of efficiency and performance as the smaller heater TIH 030m, combined with increased capacity. The advanced design of the power electronics allows features of accurate electric current control, cut-outs to avoid overheating, controls on rate of temperature increase, these are as some of the standard features in the TIH...m range.
Placing the induction coil outside the heater’s housing allows the heating of bearings weighing up to 120 kg (264 lb). The heater is equipped with thermal overheating protection to reduce the risk of damage to the induction coil and the electronics. In addition to temperature mode, the TIH 100m is equipped with a time mode for heating components other than bearings. The heater is supplied standard with three yokes and is available in two executions: 230V/50-60Hz or 400-460V/50-60Hz.

Technical data
Designation TIH 100m
SKF m20 performance 97 kg (213 lb)
Voltage, V/Hz
- TIH 100M/230V
- TIH 100M/MV
230V/50-60Hz
400-460V/50-60Hz
Bearing:
- Maximum weight 120 kg (264 lb)
- Maximum bore diameter 20 - 400 mm (0.8 - 15.7 in.)
Temperature control:
- Range 0 - 250 °C (32 - 482 °F)
- Magnetic probe Yes, K-type
- Accuracy (electronics) ± 2 °C (± 3,6 °F)
Time control:
- Range 0 - 60 minutes
- Accuracy ± 0,01 sec.
Maximum heating temperature* 250°C (482 °F)
Thermometer mode Yes
Bearing mode Yes
Power reduction 2-step; 50 - 100%
Demagnetisation according
to SKF norms (automatic)

Yes (<2 A/cm)
Can heat sealed bearings Yes
Can heat pre - greased bearings Yes
Error guiding codes Yes
Thermal overload protection Yes
Maximum magnetic flux 1,7 T
Control panel Key board with LED in remote control
Operating area (w × h) 155 × 205 mm (6.1 × 8.0 in.)
Coil diameter 110 mm (4.3 in.)
Dimensions (w × d × h) 570 × 230 × 350 mm
(22.4 × 9.0 × 13.7 in.)
Total weight, including yokes 42 kg (92 lb)
Maximum power consumption 3,6 kVA (230V)
4,0-4,6 kVA (400-460V)
Number of standard yokes 3
Standard yokes 56 × 56 × 296 mm (2.2 × 2.2 × 11.7 in.),
for heating bearings with bore diameter of 80 mm (3.1 in.) and larger
28 × 28 × 296 mm (1.1 × 1.1 × 11.7 in.),
for heating bearings with bore diameter of 40 mm (1.6 in.) and larger
14 × 14 × 296 mm (0.6 × 0.6 × 11.7 in.),
for heating bearings with bore diameter of 20 mm (0.8 in.) and larger
Core cross section 56 × 56 mm (2.2 × 2.2 in.)
Yoke storage Yes, foldable
Sliding arm No
Swivel arm Yes, large yoke only
Cooling fan No
Housing material Steel and glass filled polyamide
* Depending on bearing or work piece weight. For higher temperatures, please contact SKF.

Please contact with us for more services.

Related Products

Industrial Bearings Solutions
Mobile : +852 31691718
Website : www.tvrundown.com
Telephone : +852(3)1591338
Mail : info@tvrundown.com
Address : 05 Stanley Street Central Hongkong

Copyright © 2017 - 2019Industrial Bearings Solutions All Rights Reserved